A pick-to-light system without a single light module
Deskval Workbench lights up the bin to pick from with a projector, and confirms with a depth camera that the operator’s hand went into the right one. No modules, no wiring; when the layout changes, you move the zone on the screen.
What is pick-to-light?
Pick-to-light guides the operator with light: it shows which part to take, from which bin and how many. Instead of reading a list and searching for the bin, the operator reaches for the light, so searching takes less time and fewer wrong parts are picked.
In classic systems every bin gets a light module, and the modules are wired to a controller. Deskval does the same job with a projector and a depth camera above the bench: the light is projected onto the bin, and the camera sees the pick.
How it works
You define the bins once; the job steps take care of the rest.
- 1
Draw the bins on the screen
Drag a zone over every bin on the bench plan and link it to its part in the bill of materials.
- 2
The step knows what to pick
Each job step carries which parts it needs and how many. When the product or the variant changes, so do the bins that light up.
- 3
The projector lights the bin
The next bin lights up with its part name and quantity; the operator does not search, just reaches for the light.
- 4
The camera confirms the pick
When the hand has gone into the right bin and come out, the pick is confirmed and the next bin lights up. A hand reaching into the wrong bin meets a red warning.
More than a light: it checks the pick
Pick-to-light is part of the job step in Deskval Workbench; instruction, checks and records move in the same flow.
A wrong bin is flagged at once
A hand reaching into a bin whose turn has not come sees a red warning; the error stops before it enters the assembly.
No confirmed pick, no next step
Picking from the right bin becomes the condition for moving on.
Counted picks, one by one
For critical parts, ask for a separate reach per piece; progress shows on the bin as 1/3, 2/3.
The layout changes in minutes
When a bin moves, you drag its zone; there is no module to refit and no cable to pull.
Instruction, barcode and measurement in one step
The pick is part of the same flow as the on-screen instruction, barcode scans and measuring devices.
Take the signal to your line
Pass the correct-pick and wrong-bin signals on to your PLC, and drive a signal tower or a buzzer with them.
How it differs from light modules
The same guidance, without hardware on the racks.
Hardware
Light modules: A module on every bin, wiring and a controller
Projection with Deskval: One projector and one depth camera above the bench
When the layout changes
Light modules: Modules are removed, refitted and readdressed
Projection with Deskval: You drag the zone to its new place on the screen
Pick confirmation
Light modules: The operator presses the button on the module
Projection with Deskval: By itself, when the hand goes in and out of the bin
Wrong bin
Light modules: Takes extra sensors to notice
Projection with Deskval: The reaching hand gets a red warning at once
What the operator sees
Light modules: A light and usually a number
Projection with Deskval: Light, part name and quantity, with the instruction on the same surface
Where it pays off
High-mix assembly
When the product changes, so do the bins that light up; the operator takes the right part without checking a list.
Parts that look alike
The light tells an M4 screw from an M5, and a left-hand part from a right-hand one.
Kitting
Collect the right parts in the right quantity and order for every kit.
New operators
A new operator picks the right part from the right bin from day one.
Frequently asked questions
What hardware does the pick-to-light system need?
A projector facing the work surface and a depth camera. No light modules, sensors or wiring on the racks or the bins.
Does it work with my existing bench and bins?
Yes. You draw the bins in the software to match your own layout; the bins and the rack stay as they are. They only need to be within the area the projector and the camera cover.
What happens when the operator picks from the wrong bin?
A hand reaching into a bin whose turn has not come sees a red warning at once. The job does not move to the next step until the pick from the right bin is confirmed.
Is the batch or serial number of the picked part recorded?
Pick confirmation verifies that the hand went into the right bin. For a batch or serial number, a barcode scan is added to the same step, and the scanned value goes into the production record.
Is it suitable for order picking in a warehouse?
Deskval’s pick-to-light is designed for assembly and kitting stations: it covers the bench and rack area the projector sees. Order picking along long warehouse aisles is a different need.
Does it take programming to set up?
No. Bins are drawn by drag and drop, parts are chosen from the bill of materials, and the job steps are built in the same editor.
Related guides
What Is Poka-Yoke? Examples and How to Apply It
What poka-yoke (error proofing) is: its types, examples from everyday life and production, how to apply it in five steps, and common mistakes.
How to Write a Work Instruction: Example and Free Template
What a work instruction is and how to write one: a seven-step method, a completed example and a free Excel template to download.
See pick-to-light on your own bench
Tell us about your product and your layout, and we will work out the right setup together.