How to Write a Work Instruction: Example and Free Template
A well-written work instruction lets someone doing the job for the first time do it right, safely and to the same quality. This guide covers what belongs in one, how to write it in seven steps and a completed example; you can download the template too.
7 min readUpdated 19 November 2026
What is a work instruction?
A work instruction describes, step by step, how a single operation is done: which task, in which order, with which tool and against which acceptance criterion. Its purpose is to make the job independent of the person, so the result stays the same when the shift or the operator changes.
It is often confused with a procedure. The difference:
| Procedure | Work instruction | |
|---|---|---|
| What it describes | How a process flows between people | How one job is done by hand |
| Scope | Several departments and roles | One station, one operation |
| Who uses it | Managers, engineers, auditors | The operator doing the job |
| Example | Nonconforming product procedure | PM-200 cover assembly instruction |
What belongs in a good work instruction?
- Identification: document number, revision number and date, who prepared and who approved it.
- Scope: product or part, operation, station.
- What is needed: materials, tools and equipment, personal protective equipment.
- Steps: one action per row, in the order they are done.
- Key points and reasons: the details that make the step right, safe and easy, and why they matter.
- Pictures: a photo or a drawing; a right and a wrong example side by side where possible.
- Acceptance criteria: measurable evidence that the step was done correctly.
- Revision history: what changed, when and why.
How to write a work instruction in seven steps
- Watch the job where it is done. Write the instruction at the station, not at a desk. Watch the operator who does it best for several cycles, and film it if that helps.
- Break the job into major steps. Each step is one action that moves the work forward: “place the housing in the fixture”, “tighten the four screws”. An operation usually has 5 to 10 steps; if it has more, consider splitting it.
- Write the key points and their reasons. For every step ask what makes it right and what happens if it is done wrong. “Tighten crosswise, because only then does the cover seat evenly.” An operator who knows the reason does not skip the step.
- Add photos. A photo is read faster than three sentences. Show the part in its correct position, with a wrong example if you can, and mark where to look with an arrow or a circle.
- Make the acceptance criterion measurable. “Check carefully” is not a criterion. “Torque 0.6 Nm”, “no gap between cover and housing” and “the serial number shows on the screen” are.
- Try it with someone who does not know the job. Hand the instruction to a person who has never done the operation and only watch. Every hesitation and every question is a gap in the instruction.
- Get it approved and control the revision. Number the document, give it a revision, have it approved and collect the old copy from the station. An assembly built to an old revision is harder to spot than one built with no instruction at all.
Example: cover assembly of a socket module
The example below is a 48-second operation that fits the cover on a socket module. Each step comes with its key point and the reason for it.
| Step | What to do | Key point | Reason |
|---|---|---|---|
| 1 | Place the housing in the fixture. | Locating pins fully seated in their holes. | In a tilted housing the screws go in at an angle. |
| 2 | Scan the barcode on the board. | Hold the scanner square to the label. | Ties the serial number to the product for traceability. |
| 3 | Seat the cover on the housing. | Cable side first; do not pinch the cable. | A pinched cable can cause a short circuit. |
| 4 | Tighten the four screws crosswise. | Torque 0.6 Nm; order 1-3-2-4. | Crosswise tightening seats the cover evenly. |
| 5 | Apply the label to the lower right corner of the cover. | Label edge on the guide line. | The customer's scanner looks for the label there. |
| 6 | Do the final check and put the unit in the outgoing bin. | Scratches, a missing screw, a crooked label? | A faulty unit must not reach the next station. |
The same example, with its acceptance criteria and step times, is filled in on the “Example” sheet of the template.
Free work instruction template
Work instruction template (Excel)
Prints on one A4 landscape page. It holds a blank form, the completed example above and a short page on how to use it, and it adds up the step times for you.
Download the template (.xlsx)Free, no sign-up. Add your own logo and document number and use it as it is.
Five common mistakes
- Long sentences. Operators read the instruction while they work. If a step runs over one line, split it.
- Wording nobody can measure. “Tighten firmly” and “be careful” mean something different to everyone. Give a value or a criterion you can see.
- No photos. A text-only instruction is the one new operators make most mistakes with.
- Uncontrolled copies. An old revision left at the station is more dangerous than no instruction.
- Written at a desk. An instruction that was never tried on the floor describes how the job is thought to be done, not how it is done.
When is it time to move from paper to digital?
A paper instruction does its job at a station that makes one product and rarely changes. It stops being enough when one of these starts:
- There are many product variants, and the operator has to look for the right instruction.
- Revisions change often, and collecting old copies has become a job of its own.
- The customer asks which unit was built with which batch of material, and by whom.
- New operators take weeks to learn the job.
- Errors only show up at final inspection.
With a digital work instruction the right revision opens on the screen by itself and the operator confirms each step to move on. Barcode, measurement and camera checks become part of the step, and every job is recorded.
Frequently asked questions
What is the difference between a work instruction and a procedure?
A procedure describes how a process runs between people; a work instruction describes how one job is done at the station, step by step. A procedure answers “what and who”, an instruction answers “how”.
How long should a work instruction be?
One page per operation is a good target. If it runs past two pages, split the operation, or cut text and add photos.
Who writes the work instruction?
Usually a process or production engineer together with the operator who does the job best; quality approves the acceptance criteria. An instruction written without the operator rarely survives on the floor.
Does ISO 9001 require work instructions?
The standard prescribes no format. It requires production under controlled conditions and, where needed, documented information that defines the work to be done (ISO 9001:2015, clause 8.5.1). A work instruction is the most common way to meet that.